Home
About Us
Calendar
Fiero Documents
Merchandise
Tips
Links
Members
Message Board
Other Fiero Clubs
VIN Decoder
Speed Calculator
GFC Facebook Page
 

Author Topic: Need un vented side cover  (Read 14965 times)

0 Members and 1 Guest are viewing this topic.

GTXVette

  • Hero Member
  • *****
  • Posts: 519
    • View Profile
Need un vented side cover
« on: April 03, 2018, 07:59:37 pm »
 the lower piece behind the door On the Drivers side. my Pass side is smooth and I like that Better. need it soon, I am In Paint NOW.

GTRS Fiero

  • Hero Member
  • *****
  • Posts: 12,510
  • It is what it is.
    • View Profile
Re: Need un vented side cover
« Reply #1 on: April 03, 2018, 08:03:07 pm »
Are you looking for a fabricated part, or one someone covered up the cold air intake?

To my knowledge, there were no stock lower left quarter panels sold without the cold air intake hole.
« Last Edit: April 03, 2018, 08:50:25 pm by GTRS Fiero »

GTXVette

  • Hero Member
  • *****
  • Posts: 519
    • View Profile
Re: Need un vented side cover
« Reply #2 on: April 04, 2018, 07:57:32 am »
Interwesting,  Going to look in a few min.

TopNotch

  • The Duke of URL
  • Global Moderator
  • *****
  • Posts: 3,984
    • View Profile
Re: Need un vented side cover
« Reply #3 on: April 04, 2018, 10:14:15 am »
If you don't have an opening, how's the engine going to get air?
The more complex the mind, the greater the need for the simplicity of play.

GTXVette

  • Hero Member
  • *****
  • Posts: 519
    • View Profile
Re: Need un vented side cover
« Reply #4 on: April 04, 2018, 03:40:39 pm »
   The Inlets I speak of are placed where a rear Brake Inlet would be, the rear edge is part of wheel opening, My Pass. side is a factory looking piece so must be a OEM Part.

Fierofool

  • Global Moderator
  • *****
  • Posts: 10,708
    • View Profile
    • Georgia Fiero Club
Re: Need un vented side cover
« Reply #5 on: April 04, 2018, 06:55:19 pm »
Look on page 11 of the Formula Fastback thread.  The red one Todd has on the dolly shows the stock left rear quarter with the stock air intake.  Mike's car has a Fiero Store or Holley aftermarked scoop bolted on in place of the stock intake grill.  The fastback shows the stock right side rear quarter.  The red one and the grey one are the only way they were produced for all 5 years. 
There are three kinds of men:

1.    The ones that learn by reading.
2.    The few who learn by observation.
3.    The rest of them have to pee on the electric fence and find out for themselves.    Will Rogers

GTXVette

  • Hero Member
  • *****
  • Posts: 519
    • View Profile
Re: Need un vented side cover
« Reply #6 on: April 05, 2018, 07:40:16 am »
 So Left side has an Air Inlet but right side Does not.

TopNotch

  • The Duke of URL
  • Global Moderator
  • *****
  • Posts: 3,984
    • View Profile
Re: Need un vented side cover
« Reply #7 on: April 05, 2018, 07:49:49 am »
You can get aftermarket pieces that look like the one on this car for both sides....

The more complex the mind, the greater the need for the simplicity of play.

GTRS Fiero

  • Hero Member
  • *****
  • Posts: 12,510
  • It is what it is.
    • View Profile
Re: Need un vented side cover
« Reply #8 on: April 05, 2018, 07:55:21 am »
So Left side has an Air Inlet but right side Does not.

Correct.  IIRC, that inlet was added after initial testing.  I like symmetry, too, but the sources for side scoops are drying up.

Fierofool

  • Global Moderator
  • *****
  • Posts: 10,708
    • View Profile
    • Georgia Fiero Club
Re: Need un vented side cover
« Reply #9 on: April 05, 2018, 08:25:50 am »
You can get aftermarket pieces that look like the one on this car for both sides....


Or you can have this one after we remove it.
There are three kinds of men:

1.    The ones that learn by reading.
2.    The few who learn by observation.
3.    The rest of them have to pee on the electric fence and find out for themselves.    Will Rogers

Raydar

  • Paid Members
  • *****
  • Posts: 3,014
    • View Profile
Re: Need un vented side cover
« Reply #10 on: April 05, 2018, 10:11:03 am »

Correct.  IIRC, that inlet was added after initial testing.  I like symmetry, too, but the sources for side scoops are drying up.

Not the aftermarket scoops. They're still around.
Sage Glassworks (formerly of Fiero Warehouse) is still producing them. The ones like on the white car, above, and also the concave (IMSA) style.
Maybe even the "ribbed" IMSA style, although I seldom see them.
...

GTXVette

  • Hero Member
  • *****
  • Posts: 519
    • View Profile
Re: Need un vented side cover
« Reply #11 on: April 05, 2018, 10:24:07 am »
  the look I want is NO Scoops on either side, but in the name of even ness the scoop on the white car were good but are they on Both Sides.   All good,   that part of the car gets at least prep today, and maybe Color too.

GTRS Fiero

  • Hero Member
  • *****
  • Posts: 12,510
  • It is what it is.
    • View Profile
Re: Need un vented side cover
« Reply #12 on: April 05, 2018, 07:05:58 pm »
Some people have the intake in the engine bay.  There are several mods for this.  The great blue chop top had a V8 with the intake in the engine bay.  Of course, less power on hot air.

GTRS Fiero

  • Hero Member
  • *****
  • Posts: 12,510
  • It is what it is.
    • View Profile
Re: Need un vented side cover
« Reply #13 on: April 05, 2018, 10:34:18 pm »

Correct.  IIRC, that inlet was added after initial testing.  I like symmetry, too, but the sources for side scoops are drying up.

Not the aftermarket scoops. They're still around.
Sage Glassworks (formerly of Fiero Warehouse) is still producing them. The ones like on the white car, above, and also the concave (IMSA) style.
Maybe even the "ribbed" IMSA style, although I seldom see them.

Yeah, and Tha Driver can make them, but the Fiero Fiberglass scoops are only existing stock.

GTRS Fiero

  • Hero Member
  • *****
  • Posts: 12,510
  • It is what it is.
    • View Profile
Re: Need un vented side cover
« Reply #14 on: June 27, 2019, 09:26:48 pm »
Was there ever a pic of your car posted, after paint?  I don't recall such.