Home
About Us
Calendar
Fiero Documents
Merchandise
Tips
Links
Members
Message Board
Other Fiero Clubs
VIN Decoder
Speed Calculator
GFC Facebook Page
 
« previous next »
Pages: [1]

Author Topic: Handling problem solved.  (Read 14105 times)

0 Members and 1 Guest are viewing this topic.

TopNotch

  • The Duke of URL
  • Global Moderator
  • *****
  • Posts: 3,984
    • View Profile
Handling problem solved.
« on: May 20, 2019, 11:46:09 am »
Nobody knows it but Fierofool, but I spun out on the trial run for the Don Hulse Cruise. I was driving my silver Formula, and it just wasn't handling like it should. Well, I found the problem. The front sway bar end link bushings had disintegrated. Having a rear sway bar and no front sway bar is not good. Fortunately I had a set of Poly end link bushings already on hand, so I put them on yesterday. I'll have to see how it does now.
« Last Edit: May 20, 2019, 02:16:06 pm by TopNotch »
Logged
The more complex the mind, the greater the need for the simplicity of play.

Fierofool

  • Global Moderator
  • *****
  • Posts: 10,708
    • View Profile
    • Georgia Fiero Club
Re: Handling problem solved.
« Reply #1 on: May 20, 2019, 04:48:45 pm »
When you install the bushings, count the number of turns you tighten the nut on the first end link.  Then tighten the second end link nut the same number of turns.  If you haven't already removed the old nut, count the number of turns it takes to get it off, then go back with the same number of turns.  Having one side tighter than the other can give some problems. 
Logged
There are three kinds of men:

1.    The ones that learn by reading.
2.    The few who learn by observation.
3.    The rest of them have to pee on the electric fence and find out for themselves.    Will Rogers

GTRS Fiero

  • Hero Member
  • *****
  • Posts: 12,510
  • It is what it is.
    • View Profile
Re: Handling problem solved.
« Reply #2 on: May 20, 2019, 07:34:20 pm »
Well, at least no damage was done.
Logged

TopNotch

  • The Duke of URL
  • Global Moderator
  • *****
  • Posts: 3,984
    • View Profile
Re: Handling problem solved.
« Reply #3 on: May 20, 2019, 08:38:17 pm »
Since I have no idea how thick the original bushings were, I don't think it would matter how many turns it took to remove the nut. I tightened them by feel to as close the same as I could judge.
Logged
The more complex the mind, the greater the need for the simplicity of play.

GTRS Fiero

  • Hero Member
  • *****
  • Posts: 12,510
  • It is what it is.
    • View Profile
Re: Handling problem solved.
« Reply #4 on: May 20, 2019, 08:55:18 pm »
When I did mine, the side-to-side thing never occurred to me.  I tightened them so that they looked and felt the same.
« Last Edit: May 22, 2019, 08:02:08 am by GTRS Fiero »
Logged

NoMad

  • Hero Member
  • *****
  • Posts: 528
    • View Profile
Re: Handling problem solved.
« Reply #5 on: May 22, 2019, 12:35:03 am »
I just do mine to the listed torque spec and check after a few hundred miles.
Logged

Formula Owner

  • Newbie
  • *
  • Posts: 26
    • View Profile
Re: Handling problem solved.
« Reply #6 on: July 19, 2019, 05:12:55 pm »
I had this problem on my Formula. But I didn't really have a handling problem. I had a front end clunking problem. I replaced:
- upper & lower ball joints
- inner & outer tie rod ends
- steering rack bushing
- shocks
- upper & lower control arm bushings

And I STILL had clunking. I FINALLY noticed that my end link bushings were shot. Don't know how I did all that work without noticing that. Luckily, my rears were shot, too, so I didn't have any bad oversteer problems. After I replaced the end link bushings, the clunking finally went away, and the handling improved a lot.
Logged
Pages: [1]
« previous next »