Home
About Us
Calendar
Fiero Documents
Merchandise
Tips
Links
Members
Message Board
Other Fiero Clubs
VIN Decoder
Speed Calculator
GFC Facebook Page
 

Author Topic: WTB: TH440 Fiero compatible governor assembly  (Read 15647 times)

0 Members and 1 Guest are viewing this topic.

WV Mike

  • Full Member
  • ***
  • Posts: 155
    • View Profile
WTB: TH440 Fiero compatible governor assembly
« on: May 28, 2015, 11:28:11 am »
I got my Fiero back today from the shop with the TH440 transmission in it. My speedometer is not working because I need a Fiero compatible governor assembly for the TH440. Going to try to find one locally; however, I'm reaching out to the Fiero community for help.

Here is a link with information on the swap and what I need:
http://myfiero.oceanmoon.com/how-to/transmissions/fiero-th4404t60-automatic-transmission-conversion
« Last Edit: May 28, 2015, 11:33:54 am by SC Mike »
'88 Fiero Formula 2.8L v6

Raydar

  • Paid Members
  • *****
  • Posts: 3,014
    • View Profile
Re: WTB: TH440 Fiero compatible governor assembly
« Reply #1 on: May 28, 2015, 12:41:16 pm »
From the article, it sounds like you need a governor from a Fiero tranny that has the same final drive ratio as your TH440.
...

WV Mike

  • Full Member
  • ***
  • Posts: 155
    • View Profile
Re: WTB: TH440 Fiero compatible governor assembly
« Reply #2 on: May 28, 2015, 01:16:58 pm »
From my understanding, I need the governor, housing, and sensor. The one in the 4T60 (TH440) is the magnetic setup, which won't work.
'88 Fiero Formula 2.8L v6

WV Mike

  • Full Member
  • ***
  • Posts: 155
    • View Profile
Re: WTB: TH440 Fiero compatible governor assembly
« Reply #3 on: May 28, 2015, 05:39:45 pm »
I may have found the parts. If they are right, I'll post part numbers and where I got them from should anyone else go through this.
'88 Fiero Formula 2.8L v6

WV Mike

  • Full Member
  • ***
  • Posts: 155
    • View Profile
Re: WTB: TH440 Fiero compatible governor assembly
« Reply #4 on: June 05, 2015, 09:19:39 pm »
I received the governor assembly and put it quickly onto my transmission tonight. I was glad to see the part fit. I ordered the parts from http://www.txchange.com. I paid $40 for the parts and $14.72 for UPS shipping to South Carolina. Their part number for the governor assembly is RK84410.
'88 Fiero Formula 2.8L v6

Fierofool

  • Global Moderator
  • *****
  • Posts: 10,708
    • View Profile
    • Georgia Fiero Club
Re: WTB: TH440 Fiero compatible governor assembly
« Reply #5 on: June 05, 2015, 11:12:39 pm »
Does your speedometer work with the new part?
There are three kinds of men:

1.    The ones that learn by reading.
2.    The few who learn by observation.
3.    The rest of them have to pee on the electric fence and find out for themselves.    Will Rogers

WV Mike

  • Full Member
  • ***
  • Posts: 155
    • View Profile
Re: WTB: TH440 Fiero compatible governor assembly
« Reply #6 on: June 06, 2015, 11:53:58 am »
Yes, the speedometer is working. I just have to use my GPS to see how much off it might be.
'88 Fiero Formula 2.8L v6

Raydar

  • Paid Members
  • *****
  • Posts: 3,014
    • View Profile
Re: WTB: TH440 Fiero compatible governor assembly
« Reply #7 on: June 06, 2015, 06:50:36 pm »
Does it shift at the proper RPM?

I'm thinking that you can use your original VSS gear, and the speedo will be correct. Or as correct as it was.
I could be mistaken, however.
...

WV Mike

  • Full Member
  • ***
  • Posts: 155
    • View Profile
Re: WTB: TH440 Fiero compatible governor assembly
« Reply #8 on: June 06, 2015, 07:24:39 pm »
What is the proper RPM for it to shift at?
'88 Fiero Formula 2.8L v6

Raydar

  • Paid Members
  • *****
  • Posts: 3,014
    • View Profile
Re: WTB: TH440 Fiero compatible governor assembly
« Reply #9 on: June 06, 2015, 10:07:15 pm »
With a V6, foot to the floor, the 125 will shift at about 5500. Maybe a little higher.
...